|
Details of What's New in WinLTP 1.10
1. Added
an Experimental Log
| |
1. |
Start/Exit
WinLTP
|
|
2. |
Enter/Return from SealTest (print PulseAmp,
Rpipette, Rseal, Rs, Rm and Idc)
|
|
|
When Spreadsheet is cleared, AmpFile saved,
Protocol file opened/saved
|
|
4. |
Start/Stop Continuous Acquisition protocol
|
|
5. |
Start/Stop Main Protocol
|
|
6. |
What Sweeps have occurred (T0,T1,P0,P1,AP0,AP1)
|
|
7. |
Protocol flow (Loop,
AvgLoop, Run, Run of Run/Else, Else of Run/Else)
|
|
8. |
Evoked Single and Repeat Events
|
|
9. |
Enter time and solution change by keyboard input
|
| |
Determine which ADsweeps, Loops,
Runs and Run/Elses to show |
 |
|
 |
| Protocol run for
Experimental Log |
|
To determine which
ADsweeps, Loops, Runs and Run/Elses to show (all in this
example) |
|
 |
2. Convert
WinLTP ASCII ADsweep Files to Axon Binary Files (*.abf)
|
Convert
many WinLTP ADsweep files to:
|
| |
1. |
Many Single-sweep gap-free ABF files |
| |
2. |
Many Single-sweep episodic ABF files |
|
3. |
One Multi-sweep episodic ABF file
|
|
Note:
Stimulus information in WinLTP ADsweep files is not converted to ABF
files.
|
| WinLTP here has converted a
single-sweep ASCII ADsweep file (8N061172.P1) ... |
 |
 |
| ... into a single-sweep,
episodic Axon Binary File (8N061172.abf, loaded into
Clampfit) |
 |
|
|
3.
Increased
the number of Analysis Graphs from 4 to 12
This
was done by adding 8 Analysis Graphs to the new AnalysisPg.
 |
| Use this dialog to set the number
of Analysis Graph on MainPg and AnalysisPg |
|
|
| MainPg with 4 Analysis Graphs (as
in 1.01) |
|
New AnalysisPg with the 8 new
Analysis Graphs |
 |
|
 |
|
4.
Basic versus Advanced Mode capabilities
|
The
Advanced Mode is now required:
|
| |
1. |
To save the Expermental Log file |
| |
2. |
To convert WinLTP ADsweep files to Axon
Binary files (*.abf) |
|
3. |
For Full Multitasking. The
Advanced Mode is required to save Continuous Acqusition files while
running the Main Protocol with either the LTP Protocol or Protocol
Scripting. Before this was available in the Basic Mode.
|
| |
1. |
In the Basic Mode, ADsweep files are still
saved while running the LTP Protocol. |
| |
2. |
The Advanced Mode is still required to
save ADsweep files while running Protocol Scripting. |
| Capabilities available in the Advanced
Mode |
 |
| Capabilities available in the Basic Mode |
 |
5.
Patch-clamp
gain can now be set as mV/pA
This is to improve clarity of setting
patch-clamp gain in mV/Unit (as in 10 mV/pA) because many patch-clamps
set gain in mV/pA. This gain is included with the normal strait
gain (as in Gain = 10000000000) and gain in Units/V (as in 100 pA/V).
Return to the WinLTP Home Page
|
